Which Slic3r settings on PB Jr.

Which Slic3r settings on PB Jr.

Postby Lemm » 2013-Aug-Tue-13-Aug

Hey

Which Slic3r settings are you running on your PB Jr.?
Which speeds and so.
Are you happy with that settings?

Here is my actual
Code: Select all
# generated by Slic3r 0.9.10b on Tue Aug 20 20:27:38 2013
avoid_crossing_perimeters = 1
bed_size = 130,130
bed_temperature = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 100%
fan_always_on = 0
fan_below_layer_time = 70
filament_diameter = 1.75
fill_angle = 45
fill_density = 0.1
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 100%
first_layer_height = 0.35
first_layer_speed = 30%
first_layer_temperature = 190
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 100%
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode =
layer_height = 0.30
max_fan_speed = 100
min_fan_speed = 60
min_print_speed = 15
min_skirt_length = 0
notes =
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 100%
perimeter_speed = 30
perimeters = 3
post_process =
print_center = 65,65
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 75
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 20
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
spiral_vase = 0
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 180
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 300
use_relative_e_distances = 0
vibration_limit = 0
wipe = 1
z_offset = 0
  • 0

Printrbot Jr #11045
ACME TR10x2 Z Rod
GT2 Timing Belt with 20T aluminum pulleys
Octoprint + Raspberry Pi Wireless Printer Server
Printrbot Jr v1 -> v2 upgrade http://sdrv.ms/15fDDud
http://www.thingiverse.com/Lemm
User avatar
Lemm
ACME leadscrew
 
Posts: 357
Joined: 2013-Jul-Wed-09-Jul
Location: Berlin, Germany
Reputation: 24

Which Slic3r settings on PB Jr.

Sponsor

Sponsor
 

Re: Which Slic3r settings on PB Jr.

Postby 508Parkour » 2013-Aug-Wed-20-Aug

When I first got my PB Jr. I wondered the same thing..... Here is the forum that I started:
viewtopic.php?f=16&t=2612
You should also check out the PB Getting Started Guide:
http://printrbot.com/wp-content/uploads ... Guide2.pdf
If you go to page 5 or 6, you can see the reccomended settings.
  • 0

508Parkour
I'm an end stop.
 
Posts: 73
Joined: 2013-Feb-Tue-22-Feb
Reputation: 2

Re: Which Slic3r settings on PB Jr.

Postby SilverFingers » 2013-Aug-Wed-20-Aug

I switched to Kisslicer with my PBJR, but I would also like to see someone's slic3r settings if they have it perfect.
  • 0

Click HERE to help me win a free 3D Printer!

Printrbot Jr v1
Bowden Extruder
M8 threaded rod
Heated Bed
Lots of mods

Printrbot Rules! :D
User avatar
SilverFingers
Waiting for extruder temp...
 
Posts: 99
Joined: 2013-Jun-Sun-16-Jun
Reputation: 2


Return to General

Who is online

Users browsing this forum: No registered users and 1 guest