I recently assembled a Printrbot Jr. and was able to connect to Repetier, and when I tried to manually control the bot it gave me the error, Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting).
But when I send the bot home it will return home so I know the axes motors are working.
I tried Pronterface and had the same problems.
Also the extruder won't heat up or read temperatures.
And where can I buy a cable to connect my fan to the board?
Thanks in advance
Printrbot connects to pc but will only goto home position
4 posts
• Page 1 of 1
by Mooselake » 2013-Jun-Sun-19-Jun
In Repetier-host you should be able to check the log (drag the top of the logging area up if it's not visible.) For displayed errors.
You should be able to find a fan extension cable at many computer stores; I got one from Amazon. A 2 wire cable is best, but a 3 site will work fine - just let the extra pin hang off the side, and make sure you use the same two sides on both ends.
Kirk
You should be able to find a fan extension cable at many computer stores; I got one from Amazon. A 2 wire cable is best, but a 3 site will work fine - just let the extra pin hang off the side, and make sure you use the same two sides on both ends.
Kirk
- 0
Modified KickStarter Classic Plus 7/2012
KS Thingybot Delta Pro 10/31/16
Creality Ender 3 Pro 12/2019
KS Thingybot Delta Pro 10/31/16
Creality Ender 3 Pro 12/2019
-
Mooselake - My next printer is...
- Posts: 3625
- Joined: 2011-Dec-Tue-23-Dec
- Location: Moose Swamp, Upper Michigan, USA
- Reputation: 177
Re: Printrbot connects to pc but will only goto home positio
by Tdeagan » 2013-Aug-Sat-17-Aug
- 0
Tim Deagan
KC5QFG
(optional Dual Extrusion) Printrbot Plus V1 [3/2013]
bed stabilizers, bed levelers, Y & X belt tensioners,
50mm fan mount, LED ring light, Z-axis screw Isolators,
Z-shaft stabilizers,optional Bowden conversion, GT2 belts/pulleys,
M8x1.25 Z Screws, Flex. Z-couplers,
RAMPS 1.4 w/ LCD,
Quick Change Extruders:
Option 1- Dual hybrid geared Wade's/Bowden w/ 3mm & 1.75mm Ubis,
Option 2 - Dual direct geared Wade's w/ 3mm & 1.75mm Ubis
Option 3 - Single geared Wade's w/ 3mm or 1.75mm Ubis
Option 4 - Single belt drive Wade's w/ E3D
MIC-6 metal bed
Thingiverse Profile:
KC5QFG
(optional Dual Extrusion) Printrbot Plus V1 [3/2013]
bed stabilizers, bed levelers, Y & X belt tensioners,
50mm fan mount, LED ring light, Z-axis screw Isolators,
Z-shaft stabilizers,optional Bowden conversion, GT2 belts/pulleys,
M8x1.25 Z Screws, Flex. Z-couplers,
RAMPS 1.4 w/ LCD,
Quick Change Extruders:
Option 1- Dual hybrid geared Wade's/Bowden w/ 3mm & 1.75mm Ubis,
Option 2 - Dual direct geared Wade's w/ 3mm & 1.75mm Ubis
Option 3 - Single geared Wade's w/ 3mm or 1.75mm Ubis
Option 4 - Single belt drive Wade's w/ E3D
MIC-6 metal bed
Thingiverse Profile:
-
Tdeagan - Waiting for printbed temp...
- Posts: 149
- Joined: 2013-Feb-Fri-14-Feb
- Location: Austin, TX
- Reputation: 11
Re: Printrbot connects to pc but will only goto home positio
by Tdeagan » 2013-Sep-Sun-13-Sep
Though I'm not exactly sure which part fixed this, I got it working and talked about the details in this thread:
- 0
Tim Deagan
KC5QFG
(optional Dual Extrusion) Printrbot Plus V1 [3/2013]
bed stabilizers, bed levelers, Y & X belt tensioners,
50mm fan mount, LED ring light, Z-axis screw Isolators,
Z-shaft stabilizers,optional Bowden conversion, GT2 belts/pulleys,
M8x1.25 Z Screws, Flex. Z-couplers,
RAMPS 1.4 w/ LCD,
Quick Change Extruders:
Option 1- Dual hybrid geared Wade's/Bowden w/ 3mm & 1.75mm Ubis,
Option 2 - Dual direct geared Wade's w/ 3mm & 1.75mm Ubis
Option 3 - Single geared Wade's w/ 3mm or 1.75mm Ubis
Option 4 - Single belt drive Wade's w/ E3D
MIC-6 metal bed
Thingiverse Profile:
KC5QFG
(optional Dual Extrusion) Printrbot Plus V1 [3/2013]
bed stabilizers, bed levelers, Y & X belt tensioners,
50mm fan mount, LED ring light, Z-axis screw Isolators,
Z-shaft stabilizers,optional Bowden conversion, GT2 belts/pulleys,
M8x1.25 Z Screws, Flex. Z-couplers,
RAMPS 1.4 w/ LCD,
Quick Change Extruders:
Option 1- Dual hybrid geared Wade's/Bowden w/ 3mm & 1.75mm Ubis,
Option 2 - Dual direct geared Wade's w/ 3mm & 1.75mm Ubis
Option 3 - Single geared Wade's w/ 3mm or 1.75mm Ubis
Option 4 - Single belt drive Wade's w/ E3D
MIC-6 metal bed
Thingiverse Profile:
-
Tdeagan - Waiting for printbed temp...
- Posts: 149
- Joined: 2013-Feb-Fri-14-Feb
- Location: Austin, TX
- Reputation: 11
4 posts
• Page 1 of 1
Return to Troubleshooting talk
Who is online
Users browsing this forum: No registered users and 1 guest